One of the most common requests in an industrial analytical lab is to distinguish between “good” and “bad” samples of supposedly the same composition. For failure analysis labs, the goal is often to determine the source of contamination or defects in a production process with poor yield. Identifying contamination left behind from different cleaning procedures or after extended use is also a common request. In all these circumstances, one does not know ahead of time what chemical compounds are present. TOF-SIMS is an ideal technique for these applications because it has high sensitivity, high specificity, and parallel detection of all masses. One complication is that real-world samples usually have a complex mixture of compounds on the surface, making the TOF-SIMS spectrum difficult to interpret. Further, the use of a wide variety of different primary ion beams (e.g. Ga⁺, In⁺, Au⁺, Bi⁺, C₆₀⁺, and Ar_n⁺) has complicated the use of TOF-SIMS spectral databases for compound identification due to large changes in relative peak intensities from one beam to another.

A MS/MS capability was recently integrated into a TOF-SIMS instrument to make compound identification easier [1,2]. It allows unambiguous identification of both organic and inorganic peaks above m/z 200, where the mass accuracy is insufficient to identify the composition of a peak by its exact mass. A MS/MS spectrum from a single precursor mass is much easier to match using a spectral database compared to using the original complex TOF-SIMS spectrum. In addition, the MS/MS spectrum of a given precursor ion is independent of the primary ion used to generated it.

Several case studies will be given where MS/MS was needed to identify compounds from an analysis of industrial samples. Two modes of MS/MS will be compared and contrasted. One is based on collision induced dissociation (CID) with inert gas and the other is based on post source decay (PSD).

[1] G.L. Fisher, J.S. Hammond, P.E. Larson, S.R. Bryan, R.M.A. Heeren, J. Vac. Sci. Technol. B 34(3), 2016, 03H126-1.

[2] G.L. Fisher, A.L. Bruinen, N. Ogrinc Potočnik, J.S. Hammond, S.R. Bryan, P.E. Larson, R.M.A. Heeren, Anal. Chem., 88, 2016, 6433-6440.

Switchable ionic liquids (SWILs) are emerging green solvents in industry for cleaner separation and efficient biomass production, for instance. However, the liquid structure and composition of SWILs are not fully understood. Besides some off-line analyses using NMR and IR, our knowledge of the SWIL is quite limited. We used in situ liquid time-of-flight secondary ion mass spectrometry (ToF-SIMS) to study SWILs in this work. SWILs are introduced into a vacuum compatible microfluidic channel for analysis by liquid SIMS. Two model systems have been investigated. The first consists of 1, 8-diazabicycloundec-7-ene (DBU) and 1-hexanol with different CO₂ loadings. The second is primarily made of koechanol with various CO₂ loadings. Koechanol acts as both acid and base in the latter. Our results show two coexisting liquid phases in the two SWIL systems. This phenomenon was only hypothesized in previous theory prediction. We are able to provide the first physical evidence of the complex liquid-liquid interface using three-dimensional chemical mapping with submicrometer resolution. In addition, more complex stoichiometry is discovered as a result of SWIL formation. More importantly, we provide the first chemical spatial mapping elucidating the evolved liquid-liquid interface as a result of SWIL formation. We anticipate the more detailed molecular level understanding of the liquid structure and composition are instrumental to build the foundation for predicative material synthesis and more versatile industrial applications.

Background:

During the development of a new soft contact lens material three areas of focus; regulatory requirements, manufacturing requirements and customer needs, are often used to guide the overall activities of the material development process.

Regulatory requirements are associated with material properties that are collected using methods defined by standards organizations and accepted by regulatory bodies globally. While this data is mandatory for the registration and approval of a contact lens material it is incomplete in that it only defines the basics of the material.

Manufacturing requirements such as speed of polymerization and completeness of reaction provide critical information so that an effective material can be made in a cost effective manner.

Finally, patients will demand a material that can be worn comfortably while correcting vision over the course of the wearing schedule. Patient focused parameters such as incorporation of wetting agents that create a wettable surface as well as a robust surface that will withstand handling of the course of several weeks of wear area also critical to success.

Methods:

The ISO methods 18369-4:2006, 4.6, 18369-4:2006, 4.4, 18369-4:2006, 4.5 were used to collect bulk properties of water content, oxygen permeability and refractive index while ANSI method Z80.20.2010, 7.10 was used to collect captive bubble contact angle data (CBCA). Photo-Differential Scanning Calorimetry (Photo DSC), Gas Chromatography-Mass Spectrometry (GC-MS) and Liquid Chromatography - Mass Spectrometry (LC-MS) were used to measure polymerization kinetics and monomer consumption. X-ray Photoelectron Spectroscopy (XPS) data was collected to understand surface uniformity and product consistency while Atomic Force Microscopy (AFM) was used to assess surface morphology over the course of the wearing schedule.

Results and Conclusion:

Data summarizing the submission for samfilcon A, a 46% water, 114 Dk material will be presented. CBCA coupled with XPS data will demonstrate a consistent surface wettability and chemistry across multiple lens powers and lens lots. Photo DSC, GC-MS and LC-MS will illustrate how the lens polymerizes in two distinct time resolved phases enabling the incorporation of polyvinyl pyrrolidone wetting agent into the lens bulk and surface. Together the analytical data will provide a unique picture of the data set needed for regulatory approval along with satisfying the manufacturing requirements and patient needs for a successful ophthalmic biomaterial.

Aluminium pretreatment for bonding purposes needs to produce a stable oxide with optimal chemical and structural characteristics for adhesion with the organic resin. Contributions at the interface region can be related to adsorptive interactions as well as mechanical interlocking between the two phases. To separate between these two effects, we applied either barrier-type or porous-type oxides on two sets of specimens. This paper presents an overview of a study on the relation between oxide properties and interfacial bonding, as affected by the nature of electrolyte and the anodizing conditions, as well as changes in the chemistry of the organic resin (epoxy, phenol, silanes). A detailed characterization of different anodic oxides and its effect on the adsorption of resin-derived functional molecules was performed using X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). Results indicate significant changes in the chemical composition of the oxides as a function of the electrolyte¹. Mechanical peel test performance indicate that the initial bond strength is independent of the oxide surface chemistry, while the stability under the ingress of water is correlated to the amount of surface hydroxyls². The presence of phosphates and sulphates did not alter bonding mechanisms, only the availability of hydroxyls. Further, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) are used to characterize the geometrical modifications to the pore- and oxide structure in porous-type oxides. In addition, energy-dispersive X-ray spectroscopy (EDS) profiles were acquired on TEM cross-sections to assess the oxide structure and concentration of resin inside the pores. Linking these morphological features to peel results show that two types of modifications are crucial for the formation of a strong and durable bonding³. A minimum pore size is needed for the resin to fill the oxide pores for good initial adhesion. Surface roughness, on the other hand, was found beneficial for the durability of the bond upon the ingress of water. Overall, the results demonstrate that both surface chemistry and oxide morphology contribute to the strength and durability of an adhesive bond.

1. Abrahami, S. T., et al., XPS Analysis of the Surface Chemistry and Interfacial Bonding of Barrier-Type Cr(Vi)-Free Anodic Oxides. J. Phys. Chem. C 2015, 119, 19967-19975.

2. Abrahami, S. T., et al., Effect of Anodic Aluminum Oxide Chemistry on Adhesive Bonding of Epoxy. J. Phys. Chem. C 2016, 120, 19670-19677.

3. Abrahami, S. T., et al., Interface Strength and Degradation of Adhesively Bonded Porous Aluminum Oxides npj Materials Degradation 2017, in press.

The top few nanometers of a sample is defined as the surface. The surface is where most chemical reactions take place. There are many instances where the surface of materials are designed/functionalized in order to optimize properties and improve device performance; there are other instances where the surface becomes compromised and the material/device performance degrades following treatment and/or use. Accurate characterization is essential in order to understand material/device performance.

Auger Electron Spectroscopy (AES), X-ray Photoelectron Spectroscopy (XPS), Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS) and Scanning Probe Microscopy (SPM) are the most common, and commercially available, surface analysis techniques. These techniques provide complimentary information regarding both the composition and microstructure of the surface of a sample and often compliments bulk analysis.

In my talk, I will discuss the characterization challenges faced in an industrial setting where the surface analyst is often provided non-ideal samples and is asked to provide both a rapid and complete analysis of the sample. The criticality of talking with the person that submits the sample to understand their issue(s) and what they expect from the analysis (as well as being certain they realize possible complications) will be highlighted via real samples. I will also show a few examples where proof of principle results provided interesting data, however the data were not scientifically meaningful.

X-ray photoelectron spectroscopy (XPS) is an irreplaceable analytical tool in materials research providing information about surface chemistry and composition. The unambiguous bonding assignment relies, however, on the correct measurement of binding energy (BE) values, which is often a nontrivial task due to the lack of an internal BE reference. C 1s signal from ubiquitous carbon contamination on samples forming during air exposure, so called adventitious carbon (AdC) layers, is the most common BE reference in XPS studies. Our literature review shows that in 58% of the top-cited papers dealing with XPS studies of magnetron sputtered films published between 2010 and 2016 in peer-reviewed journals, C 1s of AdC was used as a BE reference, while, alarmingly, the remaining papers lack information about any referencing method used. Within the first group, C 1s peak was set quite arbitrary at the BE varying from 284.0 to 285.2 eV. This serious inconsistency contradicts the very notion of a BE reference, which per definition should be connected with one single-energy value.

[i] G. Greczynski and L. Hultman, ChemPhysChem 18 (2017) 1507